GIZUMO Japan Motors

Car · Subaru

Subaru 360: The ladybird that launched Subaru

The ladybird that launched Subaru. The Subaru 360 is a rear-engined, two-door city car manufactured and marketed by Subaru from 1958 to 1971. As the company's first mass-produced automobile, production reached 392,000 over its 12-year model run.

Subaru 360 model reference
Subaru 360 Model K111
1958 Subaru 360 01.jpg · Mytho88 · CC BY-SA 3.0
Unmodified image file; scaled to fit the page. Photo remains under its stated license.

At a glance

MakerSubaru
TypeCar
Engine typeGasoline engine
Length2,995 mm
Width1,300 mm
Height1,349 mm

Development

Prior to the development of the Subaru 360, Fuji Auto Works had been working on the development of a regular passenger car since 1952, and had even managed to create a prototype of the "Subaru 1500," an advanced 1500cc four-door sedan with a monocoque structure. In February 1954, the prototype of the P-1 was completed. Nearly 20 units were made. However, due to concerns about profitability and market competitiveness, the plan to commercialize it was abandoned in 1955 and development was stalled.

In September 1954 , the "New Road Traffic Control Act" was enacted, and while the dimensions of overall length x overall width x overall height (mm) remained the same (3,000 x 1,300 x 2,000), the displacement of both 2-stroke and 4-stroke engines was standardized to 360 cc.

In December 1955, Fuji Heavy Industries decided to abandon the Subaru 1500. However, on the same day, they also decided to repurpose the production line for 250cc scooter engines, which were being produced at the Mitaka Plant at the time, to manufacture a 356cc engine for light vehicles, and to begin development of a four-seater light passenger car based on this engine. This was a car that surpassed the "National Car Concept " planned by the MITI at the time.

On 17 January 1956, the first meeting bearing the name "K-10" was held in the director's office at the Mitaka Plant. The main topics of discussion were reports on the technical studies conducted at each plant and the review of the draft order for prototype production. However, since this was a matter that would determine the future of Fuji Heavy Industries.

As a design base, Sasaki made a wooden mold with nails driven into it to indicate the limits of the body shell, and it was delivered to Sasaki in early June 1956.

The clay model was completed in 1957. The production "K-10" was first widely introduced as the Subaru 360 at a press conference held at the Marunouchi headquarters on 3 March 1958. Then the Subaru 360 made his first public appearance at a public exhibition held over three days, in 28–30 March 1958.

Design

The 360 featured an air-cooled, two-stroke inline 2-cylinder 356 cc engine mounted transversely at the rear, and was introduced March 3, 1958.

As with many other small two-stroke gas-engined cars, oil needed to be premixed with the petrol (gasoline), with the fuel tank lid serving as a measuring cup. In 1964, the "Subarumatic" lubrication system provided automatic mixing via a reservoir in the engine compartment.

Floor-mounted controls located between the driver and passenger seat included choke, heater and fuel cut-off—the latter to accommodate gravity fed fuel which obviated the need for a fuel pump. The initial production featured a full metal dash board and three-speed manual gearbox, while subsequent models featured a partially padded dash with an open glove compartment, pop-out rear quarter windows, split front bench seat, map pockets, a four-speed manual and optional three-speed-based 'Autoclutch' transmission—the latter which eliminated the clutch pedal and operated the clutch via an electromagnet.

Final assembly included wheel alignment, brake testing, chassis dynometer, headlight testing, and high-pressure water spray testing.

In contrast to the Volkswagen Beetle, the 360 is much smaller, less powerful, and was not nearly as well accepted in the global marketplace. The body was of monocoque construction and used a lightweight fiberglass roof panel. In the post war period, more automobiles would switch to unibody construction, which is now the norm for passenger cars and even many light trucks. Many of the ideas came from engineers from the former Nakajima Aircraft Company, which became Fuji Heavy Industries. The "suicide doors" are hinged at the rear, which Consumer Reports noted resulted in a partially locked door pulling open in the wind during testing.

Model history and photograph may show different years or specifications. These are model-reference photographs, not vehicles offered for sale. No photographer or manufacturer endorsement is implied.

Sources and image credit

Structured record: Wikidata Q738269 · checked 2026-11-03. The At a glance table is drawn from that record; fields the record does not contain are omitted.

Text adapted from the English Wikipedia article “Subaru 360” (en.wikipedia.org), CC BY-SA 4.0 · checked 2026-11-03.